INDUSTRIAL TRADING CENTER
Varachha Road, Surat, Gujarat
GST No. 24AAFFI6374J1Z5
TrustSEAL Verified
Call 0804763887984% Response Rate
SEND EMAIL
Product Details:
| Minimum Order Quantity | 1 Piece |
| Brand | ITC |
| Output Current | 2.4 A |
| Input Phase | Single Phase |
| Input Voltage | 24 VDC |
| Frequency | 50 Hz |
| Operating Humidity | 90% max, non-condensing |
| Country of Origin | Made in India |
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Piece |
| Voltage | 220V |
| Input Phase | TWO PHASE |
| Motor Type | Induction |
| Brand | ITC |
| Output Power | 110-220V |
| Model Name/Number | DH2522MC |
| Usage/Application | Industrial |
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Piece |
| Voltage | 12V |
| Control Method | Sensorless Vector Control |
| Input Phase | Single Phase |
| Motor Type | Synchronous |
| Brand | ITC |
| Model Name/Number | STEPPER DRIVE DM 542 ITC |
| Usage/Application | Industrial |
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Piece |
| Voltage | 220V |
| Control Method | Sensorless Vector Control |
| Input Phase | Single Phase |
| Motor Type | Synchronous |
| Brand | ITC |
| Model Name/Number | DIGITEL STEPPER DRIVE DM 860H ITC |
| Usage/Application | Industrial |
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Unit |
| Brand | Ledshine |
| Output Current | 4.2AMP |
| Input Phase | DC V |
| Input Voltage | 24VDC ~ 48v CD |
| Model Name/Number | DM542 |
| Usage/Application | CNC |
| Weight | 200MG |
Additional Information:
Product Details:
| Supply voltage | 80(113)-110(155) (Typical)-150(212) VAC(VDC) |
| Logic signal current | 7 -20 mA |
| Pulse input frequency | 0-200 kHz |
| Isolation resistance | 500 Mohm |
| Parameters | DM1182 |
| Output current | 0.5-8.2 (5.9 RMS) A |
| Pin Functions | Details |
| PUL+ | Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (software configurable); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse???active both at high level and low level (software configurable). For reliable response, pulse width should be longer than 2.5μs. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals. |
| PUL- | |
| DIR+ | DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (software configurable), this signal is counter-clock (CCW) pulse???active both at high level and low level (software configurable). For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-driver wiring match. Exchanging the connection of two wires for a coil to the driver will reverse motion direction. |
| DIR- | |
| ENA+ | Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED). When use it, the ENA signal should ahead the PUL signal at least 100ms due to of soft-start feature of the DM1182. |
| ENA- | |
| FAULT+ | Fault Signal: Open collector fault output. High impedance between FAULT+ and FAULT- during normal operation and low impedance when over-voltage, under-voltage, over-current and phase error protection. MAX: 30VDC, 20mA. |
| FAULT- |
Product Details:
| Input Phase | Single Phase |
| Temperature | 25 degree C /77 degree C |
| Isolation resistance | 500 Mohm |
| Parameters | M860 |
| Output current | 7.2 (5.1 RMS) A |
| Supply voltage | +24~+80VDC |
| Logic signal current | 7 mA |
| Pulse input frequency | 0-300 kHz |
| Microstep | Steps/rev.(for 1.8o motor) | SW5 | SW6 | SW7 |
| 2 | 400 | on | on | on |
| 4 | 800 | off | on | on |
| 6 | 1600 | on | off | on |
| 16 | 3200 | off | off | on |
| 32 | 6400 | on | on | off |
| 64 | 12800 | off | on | off |
| 128 | 25600 | on | off | off |
| 256 | 51200 | off | off | off |
| 5 | 1000 | on | on | on |
Product Details:
| Temperature | 25 degree C /77 degree C |
| Output current | 1.0-4.2 (3.0 RMS) A |
| Supply voltage | +20~+50VDC |
| Parameters | M542 V2.0 |
| Logic signal current | 7-16mA |
| Pulse input frequency | 0-300 kHz |
| Isolation resistance | 500 Mohm |
The M542 V2.0 is a high performance microstepping drive based on pure-sinusoidal current control technology. Owing to the above technology and the self-adjustment technology (self-adjust current control parameters) according to different motors, the driven motors can run with smaller noise, lower heating, smoother movement and have better performances at higher speed than most of the drives in the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors.
Features:
Extremely cost-effective
Good high speed performance
Supply voltage up to +50 VDC
Output current up to 4.2A
Self-adjustment technology
Pure-sinusoidal current control technology
Pulse input frequency up to 300 KHz
TTL compatible and optically isolated input
Automatic idle-current reduction
15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
Suitable for 2-phase and 4-phase motors
Support PUL/DIR and CW/CCW modes
Short-voltage, over-voltage, over-current protections
Specifications:
Pin FunctionDetailsPUL+Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (set by inside jumper J1); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active at high level or low level (set by inside jumper J1, J2). For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals.PUL-DIR+DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J3), this signal is counter-clock (CCW) pulse,active at high level or low level (set by inside jumper J1, J2). For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-drive wiring match. Exchanging the connection of two wires for a coil to the drive will reverse motion direction.DIR-ENA+Enable signal: This signal is used for enabling/disabling the drive. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the drive and low level for disabling the drive. Usually left UNCONNECTED (ENABLED).ENA-
Product Details:
| Minimum Order Quantity | 1 Piece |
| Brand | ITC |
| Output Current | 2.4 A |
| Input Phase | Single Phase |
| Input Voltage | 24 VDC |
| Frequency | 50 Hz |
| Operating Humidity | 90% max, non-condensing |
| Country of Origin | Made in India |
Additional Information: