Easy Servo Drives

Product Details:

ES-D508 is one of the models in Leadshine ES-D series easy servo drives which can take 20-50 VDC input voltage and output 0.5 - 8.0 A continuous load-based current. It is capable of driving NEMA 17, 23, 24 and 34 (1-2 stacks) easy servo motors (stepper motors with encoders) with the position loop closed in real time.

Based on latest DSP technology and adopting Leadshine''s advanced control algorithm, ES-D508 easy servo drive applies servo control on easy servo motors. When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance.

Same as servo drives in traditional brushless servo systems, an ES-D508 easy servo drive takes encoder feedback from a driven ES-M series easy servo motor to close the position loop and eliminate the possibility of lose of movement synchronization. Therefore, loss of steps which limits adoption of stepper systems is totally eliminated in ES-D508 driven easy servo systems. Compared with constant output current in open loop stepper drive, output current from an ES-D508 servo drive to the driven motor is load based. When torque requirement is low, the output current is automatically lowered to the level of "just enough". But when the torque requirement is high, an ES-D508 easy servo drive can boost the output current quickly, up to 8.0A. This can significantly improve control system response time, offer excellent acceleration performance, and reduce motor heating by as much as 50% over open-loop stepper systems. Also, there is no torque reservation needed for an ES-D508 driven easy servo system. In an ES-D508 driven easy servo system, it always allows 100% torque implementation available from the driven easy servo motor and thus improves system high speed performance by as much as 30% over comparable open loop stepper systems. In addition, smoothness and quietness are also significantly improved in ES-D508 driven easy servo systems over steppers.

Compared with traditional brushless servo systems, cost for ES-D508 driven easy servo systems is significantly lower. They also outperform comparable traditional brushless servo systems for the features of much higher low-middle speed torque, high standstill stiffness, no hunting (shaking), no overshooting, and almost zero settling time. In addition, plug-and-play setup for almost all applications makes ES-D508 driven easy servo system much simple to set up, over hard-to-configure brushless servo systems which usual involve configurations of tens of parameters.


Features:

• Step and direction control
• Closed position loop for no loss of movement synchronization
• Operating voltage: 20-50 VDC
• Load based output current of 0.5 - 8.0 A
• High torque at starting and low speed
• No torque reservation
• High stiffness at standstill
• Significantly reduced motor heating
• Smooth motor movement and extra low motor noise
• Quick response, no delay and zero settling time
• No loss of steps; no hunting; no overshooting
• Plug-and-play and no tuning

Product Details:

With a firm commitment to quality, we are involved in offering a wide ambit of ES-D1008 Easy Servo Drives.

Detail:
ES-D1008 is one of the models in Leadshine ES-D series easy servo drives which can take 20-80 VAC or 30-100 VDC input voltage, and output 0.5 - 8.2 A continuous load-based current. It is capable of driving NEMA 23, 24 and 34 easy servo motors (stepper motors with encoders) with the position loop closed in real time.

Based on latest DSP technology and adopting Leadshine's advanced control algorithm, ES-D1008 easy servo drive applies servo control on easy servo motors. When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance.

Same as servo drives in traditional brushless servo systems, an ES-D1008 easy servo drive takes encoder feedback from a driven ES-M series easy servo motor to close the position loop and eliminate the possibility of lose of movement synchronization. Therefore, loss of steps which limits adoption of stepper systems is totally eliminated in ES-D1008 driven easy servo systems. Compared with constant output current in open loop stepper drive, output current from an ES-D1008 servo drive to the driven motor is load based. When torque requirement is low, the output current is automatically lowered to the level of "just enough". But when the torque requirement is high, an ES-D1008 easy servo drive can boost the output current quickly, up to 8.2A. This can significantly improve control system response time, offer excellent acceleration performance, and reduce motor heating by as much as 50% over open-loop stepper systems. Also, there is no torque reservation needed for an ES-D1008 driven easy servo system. In an ES-D1008 driven easy servo system, it always allows 100% torque implementation available from the driven easy servo motor and thus improves system high speed performance by as much as 30% over comparable open loop stepper systems. In addition, smoothness and quietness are also significantly improved in ES-D1008 driven easy servo systems over steppers.

Compared with traditional brushless servo systems, cost for ES-D1008 driven easy servo systems is significantly lower. They also outperform comparable traditional brushless servo systems for the features of much higher low-middle speed torque, high standstill stiffness, no hunting (shaking), no overshooting, and almost zero settling time. In addition, plug-and-play setup for almost all applications makes ES-D1008 driven easy servo system much simple to set up, over hard-to-configure brushless servo systems which usual involve configurations of tens of parameters.


Features:

• Step and direction control
• Closed position loop for no loss of movement synchronization
• Operating voltage: 20-80 VAC or 30-100 VDC
• Load based output current of 0.5 - 8.2 A
• High torque at starting and low speed
• No torque reservation
• High stiffness at standstill
• Significantly reduced motor heating
• Smooth motor movement and extra low motor noise
• Quick response, no delay and zero settling time
• No loss of steps; no hunting; no overshooting
• Plug-and-play and no tuning for most applications

Product Details:

• Advanced servo technology to combine advantages of open-loop stepper systems and AC servo systems
• Closed-loop controls to eliminate lose of steps, stall or movement synchronization
• High starting torque and quick response
• Vector control ,smooth motor movement with lower vibration&heating and quick response
• Excellent respond time, quick acceleration, and very high high-speed torque (30% over open-loop)
• Load-dependent dynamic current output from drive to motor to significantly motor heating deduction Input voltage from 150 to 230VDC; MAX 6.0A peak current output from drive to motor
• Micro step resolution value from 200-51,200 (increased by 1) via software configuration Isolated control inputs of Pulse, Direction and Enable Easy tuning for plug and play setup and built-in on-board HMI for easy setup and configuration
• Easy Servo motors with selectable encoder resolution 1000,5000 lines and output signal include A,B,Z;
• In-position and fault outputs to external motion controllers for complete system controls.
• Over voltage, over-current, and position-error protection

Click Here to View & Download Datasheet for Leadshine Easy Servo Drive ES2-3DA2206
Click Here to View & Download Specification for Leadshine Easy Servo Drive ES2-3DA2206

Sku: ES2-3DA2206 Vendor: Leadshine

Additional Information:

• Item Code: 3DA2306
• Production Capacity: 200
• Delivery Time: 1 DAY
• Packaging Details: BOX

Product Details:

Aimed at a prosperous growth in this domain, we are engaged in offering an excellent quality range of ES-DH1208 Easy Servo Drives.


Detail:
ES-DH1208 is one of the models in Leadshine ES-DH series easy servo drives which can take direct 110/120 or 220/230 VAC input voltage, and output 0.5 - 8.0 A (ES-DH1208) or 0.5 - 6.0 A (ES-DH2306) continuous load-based current. It is capable of driving NEMA 34 and 42 easy servo motors (stepper motors with encoders) with the position loop closed in real time.

Based on latest DSP technology and adopting Leadshine's advanced control algorithm, ES-DH1208 easy servo drive applies servo control on easy servo motors. When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance.

Same as servo drives in traditional brushless servo systems, an ES-DH1208 easy servo drive takes encoder feedback from a driven ES-MH series easy servo motor to close the position loop and eliminate the possibility of lose of movement synchronization. Therefore, loss of steps which limits adoption of stepper systems is totally eliminated in ES-DH1208 driven easy servo systems. Compared with constant output current in open loop stepper drive, output current from an ES-DH1208 servo drive to the driven motor is load based. When torque requirement is low, the output current is automatically lowered to the level of "just enough". But when the torque requirement is high, an ES-DH1208 easy servo drive can boost the output current quickly, up to 8.2A. This can significantly improve control system response time, offer excellent acceleration performance, and reduce motor heating by as much as 50% over open-loop stepper systems. Also, there is no torque reservation needed for an ES-DH1208 driven easy servo system. In an ES-DH1208 driven easy servo system, it always allows 100% torque implementation available from the driven easy servo motor and thus improves system high speed performance by as much as 30% over comparable open loop stepper systems. In addition, smoothness and quietness are also significantly improved in ES-DH1208 driven easy servo systems over steppers.

Compared with traditional brushless servo systems, cost for ES-DH1208 driven easy servo systems is significantly lower. Starting and low-speed huge output torque from an EM-DH1208 driven easy servo motor is way higher than torque from simliar size brushless servo motors. Such systems also outperform comparable traditional brushless servo systems for high standstill stiffness, no hunting (shaking), no overshooting, almost zero settling time, and plug-and-play setup with no tuning for most applications. In addition, plug-and-play setup for almost all applications makes ES-DH1208 driven easy servo system much simple to set up, over hard-to-configure brushless servo systems which usual involve configurations of tens of parameters.

When an ES-DH1208 easy servo drive is implemented with a LeadshineES-MH series easy servo motor, there is No Configuration Needed for almost all applications. For fine tuning or custom configurations, a user can simply use the on-board LED display to perform all the setup.

Features:

• Step based servo control
• Closed position loop for no loss of movement synchronization
• Operating voltage: 90 - 130 VAC or 127 -184 VDC
• Load based output current of 0.5 - 8.0 A
• High torque at starting and low speed
• No torque reservation
• High stiffness at standstill
• Significantly reduced motor heating
• Smooth motor movement and extra low motor noise
• Quick response, no delay and zero settling time
• Plug-and-play and no tuning for almost all applications
• Also capable of driving normal 2 phase stepper motor